Showing posts with label light. Show all posts
Showing posts with label light. Show all posts

Thursday, December 26, 2013

Touch Sensitive Light Dimmer

With IC SLB0586A from Siemens you can build a simple touch light dimmer circuit that will allow you to adjust the lamp intensity. Together with a TIC206D triac, it enables smooth regulation of light intensity from a bulb of 10W – 400W. A coil of 100µH/5A is required to suppress switching noise.

The voltage supply is obtained through R2, C2, D1 and C3 and is about 5.3V below the network potential. The touch sensor that is used to drive the IC is connected at pin 5 through two 4.7MΩ resistors, R5 and R6, in order to ensure user security.

In the adjustable touch lamp schematic we can see three selection connection , for selecting one of three modes of the IC. When the B connection is used, the light will always be ON at the last level that we used. With A or C connection the light will be ON at the minimum intensity. With B or C, the purpose of regulation is reversed with each use.

Schematic of the adjustable light with touch sensor
Circuit Project: Touch light dimmer circuit
Touch Sensitive Light Dimmer Circuit Diagram


When the sensor is touched for a short period of time (50 – 400 ms), the lamp will be ON or OFF. If the sensor is touched for a longer period of time it will start the regulation process. Warning! This touch light dimmer circuit has some points where lethal 220V is present, please do not try this project if you are not qualified.
ReadMore..

Friday, December 20, 2013

AC 220V Mains Powered Emergency Light and Alarm

This circuit is permanently plugged into a mains socket and NI-CD batteries are trickle-charged. When a power outage occurs, the lamp automatically illuminates. Instead of illuminating a lamp, an alarm sounder can be chosen. When power supply is restored, the lamp or the alarm is switched-off. A switch provides a "latch-up" function, in order to extend lamp or alarm operation even when power is restored.

Emergency Light and Alarm Circuit Diagram
Emergency Light and Alarm Circuit Diagram

Parts List:


R1 = 220K
R2 = 470R
R3 = 390R
R4 = 1.5K
R5 = 1R
R6 = 10K
R7 = 330K
R8 = 470R
R9 = 100R
D1 = 1N4007
D2 = 1N4007
D3 = 1N4007
D4 = 1N4007
D5 = 1N4007
D6 = Led
D7 = 1N4148
Q1 = BC547
Q2 = BC327
Q3 = BC547
Q4 = BC547
Q5 = BC327
C1 = 330nF-400V
C2 = 10uF-63V
C3 = 100nF-63V
C4 = 10nF-63V
LP1 = 2.5V-300mA Torch Lamp Bulb
PL1 = Male Mains Plug
SW1 = SPST Switches
SW2 = SPST Switches
SW3 = SPDT Switches
SPKR = 8 Ohms Loudspeaker
B1 = 2.5V Battery (two AA NI-CD rechargeable cells wired in series)

Mains voltage is reduced to about 12V DC at C2s terminals, by means of the reactance of C1 and the diode bridge (D1-D4). This avoids the use of a mains transformer. Trickle-charging current for the battery B1 is provided by the series resistor R3, D5 and the green LED D6 that also monitors the presence of mains supply and correct battery charging.

Q2 & Q3 form a self-latching pair that start operating when a power outage occurs. In this case, Q1 biasing becomes positive, so this transistor turns on the self latching pair. If SW3 is set as shown in the circuit diagram, the lamp illuminates via SW2, which is normally closed; if set the other way, a square wave audio frequency generator formed by Q4, Q5 and related components is activated, driving the loudspeaker.

If SW1 is left open, when mains supply is restored the lamp or the alarm continue to operate. They can be disabled by opening the main on-off switch SW2. If SW1 is closed, restoration of the mains supply terminates lamp or alarm operation, by applying a positive bias to the Base of Q2.

Note:


Close SW2 after the circuit is plugged.

Warning!


The circuit is connected to 230Vac mains, then some parts in the circuit board are subjected to lethal potential!. Avoid touching the circuit when plugged and enclose it in a plastic box.

ReadMore..

Thursday, September 26, 2013

Light Gate With Counter Using 555 And 4033

The circuit described here counts the number of times that an infrared beam is interrupted. It could be used to count the number of people entering a room, for instance, or how often a ball or another object passes through an opening (handy for playing shuffleboard). The heart of the circuit consists of - you guessed it - a light gate! Diode D1 is an IR diode that normally illuminates IR transistor T1. The light falling on T1 causes it to conduct to a certain extent. The resulting voltage on the collector of T1 should be just low enough to prevent the following transistor (T2) from conducting. This voltage can be adjusted within certain limits using P1.

As soon as an object comes between D1 and T1, the light shining on T1 will be partially or fully blocked, causing the IR transistor to conduct less current. As a result, the voltage on its collector will increase, producing a brief rise in the voltage on the base of T2. This will cause T2 to conduct and generate a negative edge at IC1. This negative edge will trigger the monostable multivibrator, which will then hold the output signal on pin 3 ‘high’ for a certain length of time (in this case, one second). At this point, two things will occur. First, a buzzer will be energized by the output of IC1 and produce a tone for approximately one second.

Light Gate With Counter Using 555 And 4013 Circuit DiagramWhen the buzzer stops, a negative edge will be applied to the clock input of IC2, causing the counter in IC2 to be incremented by 1. IC2 is conveniently equipped with an internal binary-to-BCD decoder, so its outputs only have to be buffered by IC3 and T3 to allow the state of the counter to be shown on the 7-segment display. Switch S1 can be used to reset the counter to zero. If a one-second interval does not suit your wishes, you can modify the values of R3 or C1 to adjust the time. Increasing the value of R3 lengthens the interval, and decreasing it naturally shortens the interval.

The same is true of C1. When building the circuit, make sure that T1 is well illuminated by the light from D1, while at the same time ensuring that T1 ‘sees’ as little ambient light as possible. This can best be done by fitting T1 in a small tube that is precisely aimed toward D1. The longer the tube, the less ambient light will reach T1. The sensitivity of the circuit can be adjusted using P1.
ReadMore..

Wednesday, September 25, 2013

Super Light Sensor

This "Super Light Sensor" responds to minute fluctuations in light level, auto-adjusting over the range from about 200 lux up to 60,000 lux (ie, from a modestly lit room to direct sunlight). It has lots of potential uses - eg, detecting a car entering a driveway, a person moving in a room, or wind rustling the leaves of a tree. At the same time, it has a high level of rejection of natural light variations, such as sunrise, sunset and the movement of clouds. While it is a "passive" system, it can also be used as an "active" system - ie, used in conjunction with a light beam.

Its great advantage here is that, since it responds to fluctuations in light level rather than the crossing of a specific light threshold, it is much more flexible than other typical "active" systems. It can be placed within the line-of-sight of almost any light source, including "vague" ambient light, and simply switched on. As shown, the LDR is wired as part of a voltage divider so that, between darkness and full sunlight, its output at "X" varies between about one-quarter and three-quarters of the supply voltage. A wide variety of sensors may be used in place of the LDR, including photo-transistors, photo-diodes and infrared and ultraviolet devices.

Super light sensor circuit schematic
Fig.1: light level fluctuations are detected by LDR1 and the resulting signal fed to comparator stage IC1. IC1 in turn triggers 7555 timer IC2 which is wired as a monostable and this drives transistor Q2 and a relay.

The signal from the sensor is fed to the inputs of comparator IC1 via two 150kO resistors. However, any signal fluctuations will be slightly delayed on pin 3 compared to pin 2, due to the 220nF capacitor. As a result, the pin 6 output of the comparator (IC1) switches low during short-term signal fluctuations and this triggers monostable timer IC2. IC2 in turn switches on transistor Q2 which activates Relay 1. It also lights LED1 via a 1.5kO current-limiting resistor. Trimpot VR2 allows the monostable period to be adjusted between about 3s and 30s.

As with all such circuits, the Super Light Sensor may not work as well under AC lighting as under natural lighting. If AC lighting does prove a problem, a 16µF (16V) electrolytic capacitor can be connected between the sensor output and ground to filter the signal to the comparator. When pin 3 of IC2 goes high, FET Q1 also turns on and pulls pin 2 of IC2 high. This transistor remains on for a very short period after pin 3 goes low again due to the 100nF capacitor on its gate. This "blanking" is done to allow the circuit time to settle again after the relay disengages (and stops drawing current).

LDR placement:
Super Light Sensor circuit schematic
Fig.2: the LDR should be installed inside a black tube, as shown here.

The "blanking" also makes it possible to run external circuits from the same power supply as the Super Light Sensor, without upsetting the circuit. The current consumption is less than 10mA on standby, so that battery operation (eg, 8 x AA batteries) is feasible. After building the circuit, switch on and wait for the circuit to settle. Its then just a matter of adjusting VR1 so that the circuit has good sensitivity without false triggering. With some experimentation, its possible to set the circuit to change seamlessly from natural to AC lighting. If maximum sensitivity under natural lighting false triggers the circuit under AC, then adjust VR1 to give maximum sensitivity under AC (and vice versa).

In daylight, the Super Light Sensor will typically detect a single finger moving at a distance of 3m, without the use of any lenses. It will also detect a person crossing a path at a distance of more than 10m, again without lenses. And when used as an "active" system, it will typically detect a person walking in front of an ordinary light source (eg, a 60W incandescent light-bulb) at more than 10m. Note that these ranges are achieved by placing the LDR (which is used as the light sensor) in a black tube, as shown in Fig.2. A single lens will double these distances, while the use of two lenses in an "active" system will multiply the basic range by 6 or 7.
ReadMore..

Saturday, August 10, 2013

Simple Light Dependent Resistors

LDRs or lightweight Dependent Resistors are terribly helpful particularly in light/dark sensor circuits. Normally the resistance of an LDR is incredibly high, typically as high as a thousand 000 ohms, however once they are illuminated with lightweight resistance drops dramatically.


 The animation opposite shows that when the torch is turned on, the resistance of the LDR falls, permitting current to have it.Circuit Wizard software has been used to show, the vary of values of a ORP12, LDR .
When a light-weight level of a thousand lux (bright light) is directed towards it, the resistance is 400R (ohms).


When a light-weight level of ten lux (very low light level) is directed towards it, the resistance has risen dramatically to ten.43M (10430000 ohms).

This is an example of a light-weight sensor circuit :

When the sunshine level is low the resistance of the LDR is high. This prevents current from flowing to the bottom of the transistors. Consequently the LED doesnt lightweight. However, when lightweight shines onto the LDR its resistance falls and current flows into the bottom of the primary transistor and then the second transistor. The LED lights.

The preset resistor will be turned up or right down to increase or decrease resistance, during this means it will build the circuit additional or less sensitive. Link

ReadMore..

Sunday, April 21, 2013

Light Dependent Resistors

LDRs or lightweight Dependent Resistors are terribly helpful particularly in light/dark sensor circuits. Normally the resistance of an LDR is incredibly high, typically as high as a thousand 000 ohms, however once they are illuminated with lightweight resistance drops dramatically.


 The animation opposite shows that when the torch is turned on, the resistance of the LDR falls, permitting current to have it.Circuit Wizard software has been used to show, the vary of values of a ORP12, LDR .
When a light-weight level of a thousand lux (bright light) is directed towards it, the resistance is 400R (ohms).


When a light-weight level of ten lux (very low light level) is directed towards it, the resistance has risen dramatically to ten.43M (10430000 ohms).

This is an example of a light-weight sensor circuit :

When the sunshine level is low the resistance of the LDR is high. This prevents current from flowing to the bottom of the transistors. Consequently the LED doesnt lightweight. However, when lightweight shines onto the LDR its resistance falls and current flows into the bottom of the primary transistor and then the second transistor. The LED lights.

The preset resistor will be turned up or right down to increase or decrease resistance, during this means it will build the circuit additional or less sensitive.


ReadMore..

UV Torch Light

UVrn (ultra-violet) LEDs can produce crowd pleasing effects when their gentle rnis permited to intrude with certain colours, particularly with rnreflected light underneath near-dark conditions. Also try shining some UV rnlight on a diamond.

Circuit diagram :
UV Torch Light-Circuit Diagram
 UV Torch Light Circuit Diagram

Mostrn UV LEDs require about three.6 V (the ‘blue’ diode voltage) to gentle. Here, arn MAX761 step-up swaping IC is used to provide constant current to biasrn the UV diode. The IC hires PWM in high-cur-rent mode and rnautomatically modifications to PFM mode in low or medium energy mode to shop tons of rn(battery) energy. To enable it for use with two AA cells, the MAX761 isrn configured in bootstrapped mode with voltage-adjustable feedback. Up torn 4 cells may be used to power the circuit however they are going to add more rnweight than you need to for a torchlight. 

Torn lengthen the switch life, R1 is connected to the IC’s SHDN (shutdown) rnpin. Less than 50 nA can be measured in shutdown mode. Electrolytic rncapacitor C1 is used to decouple the circuit supply voltage. With-out rnit, ripple and noise may just cause instability. The one inductor within the rncircuit, L1, can have any value between about 10 and 50 µH. It stores rncurrent in its magnetic container whereas the MOSFET throughout the MAX761 is rnswitched. A toroid inductor is most popular on this position as it is going to rnguarantee low stray radiation. D1 must be a rather quick diode so rndon’t be tempted to make use of an 1N400x as a end result of it has a too gradual recovery rntime.
Thern circuit efficiency used to be measured at about 70%. R2, the resistor on the rnfeed-back pin of the MAX761 effectively decides the quantity of rnconstant present, I, despatched in the route of the UV LEDs, as follows: R2 = 1.5 / I
where I will doubtless be between 2 mA and 35 mA. 

Zenerrn diode D4 clamps the output voltage when the weight is disconnected, whichrn may just occur when one of the vital UV LEDs breaks down. Without a load, the rnMAX761 will change L1 right up to the raise voltage and so wreck rnitself.

Author : Myo Min
ReadMore..

Friday, April 12, 2013

LM317 Automatic Low Cost Emergency Light

Here is an emergency lighting based on white LEDs offer the following advantages:

1. It is very bright thanks to the use of white LEDs.

2. The light turns on automatically when the mains fails and shuts down when power resumes.

3. It has its own office. When the battery is fully charged, the charging stops.

The circuit consists of two parts: the charger from the socket and the power LED part driver.The Charger is built around the 3-terminal adjustable regulator (IC1) LM317, while the LED driver is built on part of the transistor BD140 (T2). In the power charger power transformer in the AC input is a step down to give a 9V 500mA bridge rectifier consisting of diodes (IN4007x4). Filter capacitor (25v/1000uf) to eliminate the ripples. Unregulated DC power is fed to IC1 pin 3 and provides a charging current through the diode IN4007 (D5) and limiting resistance (16ohm) R16. By providing pre-k 2.2 (VR1), the output voltage can be adjusted to provide the required charging current. When the battery may require a 6.8V, and the barrier makes the charging current regulator (IC1) to find a path through the transistor BC547 (T1) to ground and stops charging. LED driver section is used a total of twelve 10 mm white LEDs.

Circuit diagram :

LOW-COST-AUTOMATIC-EMERGENCY-LIGHT-e1297471252686Automatic Low Cost Emergency Light LM317  Circuit diagram

All LEDs are connected in parallel with the resistance of 100 ohms in series with each other. junction common anode for all twelve LED is connected to the collector of PNP transistor T2 and the emission level of the transistor T2 is directly related to the positive terminal of 6V battery. Unregulated DC voltage produced by the cathode junction of Bridge (diodes), is fed to create a transistor T2 through a resistor of 1k. When the voltage is available, the fund is still high transistor T2 and T2 does not happen. The lights are off. On the other hand, if the power does not, the transistor T2 will be a small fund and it does. This causes all the LEDs (LED1 through LED12) is lit. Network, as it is available, download and keep the lights off the battery as an indicator of transistor T2 is cut-off. During the blackout, the workload is steady and makes the battery will light up.

Assemble the circuit on a general purpose PCB and enclose in a cabinet with enough space for the battery and switches. Mount the LED in the housing to illuminate the room. A hole in the box must be drilled to connect the 230V AC input to the transformer primary. I tested the circuit with twelve white 10 mm LEDs.You can use several diodes, provided that the total energy consumption does not exceed 1.5. Driver transistor T2 can provide up to 1.5 In accordance with a proper heat sink.

Source : freecircuit.net

ReadMore..

Thursday, April 11, 2013

Push Bike Light

Automatic switch-on when it gets dark, 6V or 3V battery operation
This design was primarily intended to allow automatic switch-on of push-bike lights when it gets dark. Obviously, it can be used for any other purpose involving one or more lamps to be switched on and off depending of light intensity. Power can be supplied by any type of battery suitable to be fitted in your bike and having a voltage in the 3 to 6 Volts range.
The Photo resistor R1 should be fitted into the box containing the complete circuit, but a hole should be made in a convenient side of the box to allow the light hitting the sensor. Trim R2 until the desired switching threshold is reached. The setup will require some experimenting, but it should not be difficult.
Circuit diagram:
Push-Bike Light Circuit Diagram
Push-Bike Light Circuit Diagram
Parts:
R1_____________Photo resistor (any type)
R2______________22K 1/2W Trimmer Cermet or Carbon type
R3_______________1K 1/4W Resistor
R4_______________2K7 1/4W Resistor
R5_____________330R 1/4W Resistor (See Notes)
R6_______________1R5 1W Resistor (See Notes)
D1____________1N4148 75V 150mA Diode
Q1_____________BC547 45V 200mA NPN Transistor
Q2_____________BD438 45V 4A PNP Transistor
LP1____________Filament Lamp(s) (See Notes)
SW1_____________SPST Toggle or Slider Switch
B1______________6V or 3V Battery (See Notes)
Notes:
  • In this circuit, the maximum current and voltage delivered to the lamp(s) are limited mainly by R6 (that cant be omitted if a clean and reliable switching is expected). Therefore, the Ohms Law must be used to calculate the best voltage and current values of the bulbs.
  • For example: at 6V supply, one or more 6V bulbs having a total current drawing of 500mA can be used, but for a total current drawing of 1A, 4.5V bulbs must be chosen, as the voltage drop across R6 will become 1.5V. In this case, R6 should be a 2W type.
  • At 3V supply, R6 value can be lowered to 1 or 0.5 Ohm and the operating voltage of the bulbs should be chosen accordingly, by applying the Ohms Law.
  • Example: Supply voltage = 3V, R6 = 1R, total current drawing 600mA. Choose 2.2V bulbs as the voltage drop caused by R6 will be 0.6V.
  • At 3V supply, R5 value must be changed to 100R.
  • Stand-by current is less than 500µA, provided R2 value after trimming is set at about 5K or higher: therefore, the power switch SW1 can be omitted. If R2 value is set below 5K the stand-by current will increase substantially. 

http://www.ecircuitslab.com/2011/07/push-bike-light.html
ReadMore..